Home > Hard Drive > Best Config For 4 IDE Devices?

Best Config For 4 IDE Devices?

Contents

Source Code © 2007-2017, Adam Scheinberg, except where noted Reader comments are owned by the poster. This is why I did. Inside your computer, you generally have two (2) IDE hard drive controller connections. Open up your computer case.

Each channel can have 2 devices on it. Brian Cooley found it for you at CES 2017 in Las Vegas and the North American International Auto Show in Detroit. red or blue stripe on the cable matches up to pin 1 on the drive connector.C. running on my machine for approx 2 yrs by SlyRaskal / July 22, 2005 3:00 AM PDT In reply to: Mixing SATA and IDE drives in a system?

Ide Hard Drive Jumper Settings

Follow this Windows 10 Redstone 2 14894 … How to Update Windows 10 to Threshold 2 with Backups?. 2015-12-01 14:57:14 Tracy King - Here in this passage you’ll find detail steps Sure enough, the BIOS shows two devices loaded and functional. A Cable Select cable can be used with master/slave drive jumpering. More Resources IBM Drive Support Website Longer 80wire cables?

NOW Adventure Animals Auto Culture Entertainment Health Home & Garden Lifestyle Money Science Tech Video Shows Quizzes Follow us Facebook YouTube Twitter Pinterest Like HowStuffWorks on Facebook! If you want to make it the master or the slave, you will have to look around the drive to find where the instructions are. Flag Permalink This was helpful (2) Collapse - Mixing Drives by kbennett50 / July 23, 2005 7:08 AM PDT In reply to: Mixing SATA and IDE drives I have a mobo Ide Master Another way that manufacturers use to make sure that the cable is not reversed is by using a cable key.

I had to rename my drives to a drive letter beyond the H drive. How To Connect Ide Hard Drive To Sata Motherboard Initiate changes. Supposedly, the cables used for Cable Select will be clearly marked, with each connector labeled as Device 0 (or Master) or Device 1 (or Slave). http://www.tomshardware.com/forum/165494-31-best-configuration If you want to do that you'll just have to make sure that it's plugged into the right part of the cable.

Make sure the power is plugged in and everything is connected securely. What Is The Voltage Of The Red And Yellow Wires On Most Power Supplies? Missing floppy cable.B. Four if you never touch anything in your system. Install the new drive on the secondary IDE channel and jumper it as cable Master.

How To Connect Ide Hard Drive To Sata Motherboard

On even older mainboards you'll find a 32 GB limit. http://www.easeus.com/resource/install-ide-hard-drive.htm D: This could work. Ide Hard Drive Jumper Settings After boot windows xp/operating system on HD SATA, i re-activate IDE HDs and after backup data, repartitioned like i want. 5. Ide Cable Select Enable LBA mode and UDMA mode, if applicable.

Cable-Select Option (Default) - Use with Ultra ATA cables. First device Master and the second cable select.C. Sorry, there was a problem flagging this post. When the computer boots it includes the converted drive in a transparent manner. How Many Hard Drives Can Be Connected To A Single Ide Cable

This is not a problem as long as each device is on a separate interface, but adding support for a second drive on the same cable took some ingenuity. The drive can be a SATA or PATA hard disk drive (2.5" or 3.5"), or it could be any kind of optical drive, such as a SATA DVD or legacy CD Install the new drive on the primary IDE channel and jumper it as cable select.D. This is where you want to put an IDE drive into a SATA-only motherboard or vice versa.

A couple of things to consider though: 1. Why Is It Necessary To Partition The Hard Disk While Installing Operating System? If the limit capacity jumper is installed you will need to use a drive overlay program such as the one installed by Disc Wizard Starter Edition. Disruptive posting: Flaming or offending other usersIllegal activities: Promote cracked software, or other illegal contentOffensive: Sexually explicit or offensive languageSpam: Advertisements or commercial links Submit report Cancel report Track this discussion

I'm using an Asus P4P800-VM mobo and it requires an advanced (not for beginners says the user guide) BIOS setting to use both serial-ata and parallel-ata devices.

  1. Flag Permalink This was helpful (0) Collapse - Ahh, that never seems to work.
  2. If you scroll up and look at the motherboard connector at the beginning of this article, you'll see the 19th pin removed so that these cables can't be connected the wrong
  3. In fact, there is no pin at that position.
  4. Although the Cable Select specification may simplify things in the future, there will probably be lots of confusion, especially on legacy systems, as this starts to be introduced.
  5. by R.

so it installed onto C: and put a windows folder on D: as well as the stuff already there.that just blew my mind so i thought i better get sum help>i The IDE HD had to be on the secondary IDE cable in order for it to be recognized by the sata drive. They look this this 99% of the time: [ The smaller one on the very top is a floppy drive controller connection ] There is a Primary & Secondary connection located How Many Ide Controllers Are Available On Most Motherboards Flag Permalink This was helpful (1) Collapse - I've had this config.

My hard drive is slow: Make sure you have your CD/DVD drives plugged into a different channel/cable. Many drives feature an option called Cable Select (CS). It also offers some basic and advanced features like create, delete, resize/move, format, copy partition for better Windows hard disk management. Today it's usually called PATA (Parallel ATA).

Along one side of the cable is a stripe. I only noticed it because it was on the latest list and easy to get to.Think it over.Bob Flag Permalink This was helpful (0) Back to Storage forum 29 total posts A: 1 Harddrive. A device is in a problem state or not functioning properly.

Partition the drive. What does this mean? by Mad53704 / December 4, 2006 12:48 PM PST In reply to: New SATA HD booting mantining old IDE HDs. by R.

Cable Select is defined in the ATA-2 and ATA-3 specifications. Please read the Site Guide before using this material. 12 You just installed a second IDE slave hard drive to the primary controller in your Windows 9x system.