Home > Hard Drive > Best Way To Pull Out IDE Cable?

Best Way To Pull Out IDE Cable?

Contents

Sincerely, Disk Disposing Ahhh the hassle of old hard drives. Don't spray any liquids, especially flammable ones, near power connectors. Use a marker pen to mark "M" (master) near the middle drive connector and "S" (slave) near the far drive connector to keep them straight. Using removable drive bays This entire cable-select adventure was prompted by our need to move drives around a lot, and the first thing we found were these great removable drive bays

The area where the DVD-ROM sits is near the hard drive, sometimes in the shelving area where the DVD-ROM is placed. I will let you know if it works as it has by putting theCD/DVD drive in an enclosure.

February 14, 2014 Johnny5 Is there a similar method/hdwr to do the same I was just visiting my cousin Henry when the hard drive in his wife's old Penium MMX failed. Take off immediately all contaminated clothing. https://forums.techguy.org/threads/best-way-to-pull-out-ide-cable.174346/

How To Remove A Hard Drive

This connector will usually be a lot more snug than the IDE ribbon cable. Help answer questions Learn more 156 Does this site look plain? Video Tips If at any point you are worried if you're removing the correct cables or components, consult your owner's manual to make sure you're on the right track. Same for the colored side of IDE cables.

Privacy Policy | Term of Use | Posting Guidelines | Archive | Contact Us | Founding MembersPowered by vBulletin® Copyright ©2000 - 2012, vBulletin Solutions, Inc. In any case, it needed replacing, so the first job for Henry was to back up all the data that could still be accessed on floppy, then to remove the old To have the will to be responsible for one's self." - Stirner forkbomb View Public Profile Visit forkbomb's homepage! Laptop Hard Drive Again, do not cut the conductor itself.

w5set View Public Profile Find all posts by w5set « Previous Thread | Next Thread » Thread Tools Show Printable Version Email this Page Display Modes Linear Mode Switch to Hybrid Hard Drive Enclosure No pins should be pulled from the master connector. Style Default Style Contact Us Help Home Top RSS Terms and Rules Copyright © TechGuy, Inc. http://www.tomshardware.com/answers/id-1934041/remove-motherboard-power-cable.html Discussion in 'Hardware' started by computerpain, Oct 24, 2003.

As long as the IDE connector on the motherboard grounds pin 28, there is no software configuration required to enable the cable select mechanism. External Hard Drive Don't wiggle it. When you replace or upgrade any hard drive, you want to make sure that the jumper settings for Master/Slave selection on older drives are set correctly. GRUB2 101: How to Access and Use Your Linux Distribution's Boot Loader 7 Ways To Free Up Hard Disk Space On Windows Follow @howtogeek More Articles You Might Like ABOUT About

Hard Drive Enclosure

The resulting cable should look roughly like this: We've had a suggestion to use Star Brite's "Liquid Electrical Tape", and it looks perfect for this application. http://www.wikihow.com/Remove-a-Hard-Drive If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members. How To Remove A Hard Drive There's hardly a geek around, or even casual computer owner for that matter, that doesn't have a few old drives squirreled away. Hard Drive Recovery About eHow Advertise Write For eHow Contact Us Connect with us Terms of Use Report Copyright Ad Choices en-US Privacy Policy Mobile Privacy leafgroup.com © 1999-2017 Leaf Group Ltd.

Solder the pin-28 wire to the exposed pin-40 wire, grounding the CS line to the master connector on the end. The only problem is that hardly anyone makes a dock that supports both IDE and SATA connections anymore (neither the product sample we linked to nor it's competitors do). We all subscribe to the theory, but I hope your data was well backed up. This site uses advanced css techniques Steve Friedl's Unixwiz.net Tech Tips Using IDE Cable Select Home Contact About TechTips Tools&Source Evo Payroll Research AT&T 3B2 Advisories News/Pubs Literacy Calif.Voting Personal Tech Sata Cable

Advertisements do not imply our endorsement of that product or service. If you feel unwell contact Doctor or Poisons Information Centre. (Show the label if possible). well now......thats an excellent idea, you could use some hot glue and affix it into the lid too.

thanks for your sugestion.

Peter

please upload the pictures of back side of this breadboard please Seve __________________ Registered Linux User: #384977 .................................................. ............

Jammer1010 replied Feb 1, 2017 at 7:07 PM HP Desktop Stuck On Black... Starting with pin one - the edge with the red stripe -- count to the 28th wire and mark it with a pen. So I elected here because it has nothing to do with Linux.

WD-40 is penetrating oil.

These setting are normally shown on the label on the face of the drive, as to the right. JOIN THE DISCUSSION (10 REPLIES) February 12, 2014 TheGift73 Surprised you didn't explain that they may have to Take Ownership on old NTFS drives. In our experience this is done very easily, and this prevents the ground on this wire from reaching the drive itself, leaving it floating as a slave. Just pull harder or use a small flat-head screwdriver to pry it loose. __________________ There is no 'CTRL' button on Chuck Norris's computer.

DiscoverC Home Decor & Repair Crafts Food & Drink Garden Entertaining Fashion & Beauty Holidays Tech Personal Finance Cars Pets Legal Honest Hacks FOLLOW US î‚• î‚“ î‚” U Search U bbfuller View Public Profile Find all posts by bbfuller #7 14th July 2008, 03:22 PM jtang613 Offline Registered User Join Date: Apr 2004 Location: Ottawa, Canada Posts: 1,931 We need to somehow ground this line, and fortunately the IDE cable has several of these. Strip about one centimeter of insulation from this wire, exposing the conductor.

See the Links below for more Help and those much wanted extras ... :) Read This First Fedora 10 & 9 Installation Script and Guide The easyLife Installation RPM MJMwired Fedora Just remember that we're showing an EIDE (parallel interface) hard drive swap on this page. Vapours potentially cause drowsiness and dizziness*. * (limited evidence) SAFETY: Do not breathe gas/fumes/vapour/spray.